How To Tie Into A Camera Feed

In this article, there are five ways you can connect your Security IP Camera to your computer. And we will cover the steps on how y'all should do it without a router, without internet, without a DVR/NVR or without its receiver. The following table summarizes the important information near connecting IP camera to your computer for your reference.

Camera types:	POE camera or WiFi camera
Bone(operation arrangement):	Windows or Mac
Cable:	2-in-ane or 3-in-one cablevision attached from the camera
Remotely access by:	Camera'due south UID

Note: First yous should install the security camera in the correct place. You can refer to How to Install Home Security Cameras Successfully.

v Methods to Connect Your Security IP Camera to PC/Mac：

To get in easier for you to discover the right solution, you tin can click and jump straight to the section you want.

For case, if your camera is a PoE camera, then you can cull choice iii or four.

1. Connect Straight to PC/Mac (without Net)
2. Connect via Router (with Internet)
3. PoE (Wired) Camera without Injector/Switch
4. PoE (Wired) Camera with Injector/Switch
5. Connect a CCTV Photographic camera System to PC/Mac

Important Note: The methods recommended below may NOT apply for the battery-powered security cameras, which crave initial setup on your phones.

Connect a WiFi or PoE Photographic camera Straight to PC/Mac (without Internet)

Here's how to connect your security IP camera directly to a PC/Mac without an NVR or DVR, without a router network, without WiFi, and without any costs or complicated configurations.

you need to gear up the camera'due south power adapter and a network cablevision.

i. Get your security photographic camera charged.

Utilize the power adapter to get the camera plugged-in and charged. Commonly, when you buy a WiFi IP photographic camera, it comes with a power adapter. For a PoE camera, ask the supplier and buy one that's workable for the camera.

2. Use the network cable to connect to the camera and the reckoner.

Usually there would be a 2-in-1 or iii-in-1 cablevision attached from the photographic camera. Find the network connector from that cablevision and use the network cable to connect to it. So connect the other terminate of the network cable to the calculator. If your calculator has a network already, disable it – make certain your estimator is offline. Connect IP Camera Directly to PC

iii. Browse and find out the security photographic camera's IP address on the calculator.

At present the security camera is connecting to your reckoner basically and physically. But you lot still tin't view the camera on the reckoner. What you demand to do at present is to scan and detect out the camera's IP accost. In that location should exist surveillance software from the aforementioned supplier with the camera. Take our test as an instance. We have Reolink Customer on the computer. Launch it and information technology will automatically scan all the cameras in the aforementioned local LAN and evidence the default IP accost (every camera has a default and unique IP address when it leaves the mill). Piece of cake peasy! Camera IP Address

iv. Change the computer'southward IP address to the same network prefix of the IP photographic camera.

So in Step 3, y'all become your security camera's default IP address. In our test, the default IP address of the camera we use is 192.168.177.100, and now you need to modify your reckoner'southward IP address to 192.168.177.x, where 10 identifies the node/host and is the number between 2 and 254. And so let'due south say the computer's IP address is 192.168.177.12.

IP address 101: An IP address consists of two parts – one belongs to the network address and one belongs to the node address. All nodes on a given network share the same network prefix but have a unique host number.

Now to change the computer's IP accost (we take Windows x equally an case):

i) Press the Windows + R keyboard shortcut to bring out the Run box.

2) Enter "ncpa.cpl" and open the "Network Connections" window.

Computer Run Box

3) Correct-click your computer' network adapter and select "Backdrop".

Network Adapter Properties

four) Select your estimator'southward Internet Protocol Version and click "Backdrop".

Internet Protocol Properties

5) Select "Use the following IP address" and alter the IP address into 192.168.177.12.

Change Computer IP Address

And washed. Now your IP camera is connecting directly and communicating with your PC, considering they are now in the aforementioned little LAN. You can spotter your IP camera with Reolink Client on your computer.

Important: Since there is no router network, the IP camera would not transmit data or transport alarms to your phone. Still, you lot can record and save all the footage onto your reckoner.

If you're gonna use your IP camera with the computer all the time similar this (without router network), you'd better change the default condition of your IP photographic camera's IP accost to the static to keep information technology the same all the time, because each time you reboot the IP camera, its IP accost will exist changed and you lot volition demand to exercise all the steps to a higher place again. To proceed the IP camera'due south IP address the same all the time, caput to "Device Settings" and "Network Full general" on the Client (Reolink Client in our examination), and choose "Static" for "Network Access". And done. Static IP Address for Camera

Connect a Wireless/WiFi Photographic camera to Computer via Router (with Cyberspace)

If you do accept WiFi network and need to remotely see the IP photographic camera when you're not there, you tin can connect your wireless or WiFi camera to computer wirelessly via your router. Please note that you demand to have, at least, a power adapter for the camera, a network cable, and a router.

1. Get your WiFi security photographic camera charged.

Use the power adapter to get the camera plugged-in and charged.

2. Apply the network cable to connect to the camera and the router.

A WiF camera needs to connect to the router with a network cablevision for initial setup, because the new camera itself wouldn't recognize and car-pick up a network that it never uses. Merely after the right WiFi settings can you disconnect the cable from the camera and the router. And yes again, commonly there would exist a 2-in-1 or 3-in-one cable attached from the WiFi photographic camera. Find the network connector from that cable and use the network cable to connect to it. Then connect the other end of the network cable to the router. Connect WiFi Camera to PC

3. Sentinel the IP camera on PC/Mac

On the reckoner, launch the surveillance software to add together the camera and watch alive view directly. In our test, nosotros open Reolink Customer. Since the computer and the camera are in the same network (using the same router network), Reolink Client automatically searches and displays the camera directly. Click "Start" and you lot can view the camera on PC. And yous can set upwardly the configurations for all the functions you desire the photographic camera to have.

iv. Gear up upward WiFi settings and remove the network cable.

Do think to make the WiFi settings for the camera. On the software, navigate to "Device Settings" and "Network". Choose the WiFi network and enter the password, and done. Cameras from the different brands would have different WiFi settings. Delight refer to the guides you get from your supplier. Afterward that, remove the network cablevision, and so the security IP CCTV camera connects to the computer wirelessly.

Important: If you need to see the IP camera from some other figurer that is non in the same network, you demand to input the camera's UID into the software to remotely admission the camera.

Connect a PoE (Wired) IP Photographic camera to Computer without PoE Injector/Switch

Connecting a PoE wired IP camera to a computer via the router is similar to that of a WiFi photographic camera, and even much easier – you don't demand to use a ability adapter, ready up the WiFi and remove the network cable. And you need at least 1 network cable, and a router with PoE capability to complete the setup.

ane. Use the network cablevision to connect to the photographic camera and the router.

PoE (Power over Ethernet) ways you can merely use a single network cable for both video and power manual. So merely connect the camera to the router via the network cable, and the camera will get power supply and network admission. Cloud Storage Please make sure your router has the PoE feature. If non, try the next method.

2. Watch the IP photographic camera on the computer.

On the estimator, launch the surveillance software to add the photographic camera and watch alive view straight. In our test, we open Reolink Client. Since the computer and the photographic camera are in the same network, Reolink Client automatically searches and displays the camera directly. Click "Start" and you can view the camera on PC. And you lot can set up the configurations for all the functions you want the camera to have.

Important: If you demand to encounter the IP camera from some other computer that is not in the aforementioned network, y'all demand to input the camera'southward UID into the software to remotely admission the camera.

Connect a PoE (Wired) IP Camera to Computer with PoE Injector/Switch

If your router does non back up PoE, yous need a PoE injector or PoE switch to help connect your IP camera to PC.In social club to consummate the setup you need at least a network cable, a router, and a PoE injector or PoE switch. Since the steps on how to connect a PoE IP camera to PC via PoE Injector/switch are quite the aforementioned to that of connecting without a PoE Injector/switch, we'd like to brand it more simpler to empathize here.

1.connect the security camera, router and PoE injector

Connect all the devices as the picture showed below, brand sure your wireless IP camera is connected to a power supply. PoE Camera Connecting to PC

ii. Open Reolink Client & add the camera direct

You tin now open up Reolink Client on your figurer, add the camera and watch live view directly. If you need to run across the IP camera from another computer that is not in the same network, yous need to input the photographic camera'southward UID into the software to remotely access the photographic camera.

Important: Once yous connect the PoE IP camera to the PoE injector or switch which is connected to a router via Ethernet cables, you've successfully connected the camera to the network. For a wireless IP camera, y'all demand to utilize a network cablevision to connect it to the router if you lot haven't ready the WiFi network configuration. And then the wireless IP photographic camera is in the network. You tin fix the WiFi configuration later on to brand the wireless IP camera connect wirelessly.

Connect a CCTV Camera System to PC/Mac (with or without Network)

If yous are using a CCTV camera system, similar the Reolink PoE kit RLK8-410B4, instead of unmarried security camera, you may need the following tutorial. A CCTV photographic camera system often take their own proprietary networks, and tin work with and without your router network.

1. How to connect a CCTV security camera organisation to a computer without router network

Connect all the cameras to the NVR:When you receive the new IP camera system yous bought, connect all the devices you got – connect the NVR to your reckoner's monitor and the mouse, use the power adapters to charge the NVR and cameras, etc. For a WiFi system, in one case the WiFi NVR and the WiFi cameras are charged, they connected to each other automatically and would starting time to communicate. For a PoE system, connect the PoE cameras to the NVR via the network cables provided.
Start watching the IP cameras:The startup and setup wizard will pop up to guide you to sentry your cameras and practise other configurations.

At present you can see all the IP cameras on your monitor and start recording.

2. How to connect a CCTV security camera system to a computer with router network

Exercise the footstep 1 shown above again.
Connect the NVR to your router via the network cable provided.
Start watching the IP cameras.

The startup and setup wizard will popular upwardly to guide you to watch your cameras and do other configurations. If you need to see the IP cameras from another computer that is not in the same network, y'all demand to input the NVR'southward UID into the software to remotely admission the cameras.

Inforgraphic:

The infographic beneath also covers our 5 methods to connect IP security camera to PC/Mac . Hope this tin can be helpful to you.

How to Connect Security Camera to PC

Tertiary-Party Software to Connect IP Camera to PC/Mac

Yous can also opt for third-party software to connect and set upwardly a security camera on the computer. Make sure the software tin handle all the cameras on the network and support all the features for the cameras. Commonly, the third-political party software has several versions. And if you lot desire to apply full features of the camera, you need to pay for a premium version. If your security IP camera is not working properly as expected or if you become whatsoever issues, you can attempt the top 10 solutions to fix IP cameras not working.

For whatever questions, please don't hesitate to go out information technology in your annotate. I will respond as before long as possible.

Source: https://reolink.com/connect-security-ip-camera-to-pc/

Posted by: carterhinatimsee.blogspot.com